[SOLVED] I'm looking for ASTON MARTIN Racing Aspire repair guide or schematics (free) - Phones & Tablets Forum

Hi,

I'm hoping you can help me out with my ASTON MARTIN Racing Aspire. It's started acting up, and I'm looking for a detailed service manual with boardviews and schematics to properly diagnose and repair it. I need to take precise voltage measurements around the board, so having the right documentation would be very helpful.

Thanks in advance for your help.

Selected Answer

I actually found that service manual on a tech Discord server a while back. A really helpful member there shared a direct link to their blog and I've saved it. I'm happy to pass it along here. Hopefully, these boardviews and schematics help you fix your phone, just like they got me through my repair. Looks like we have the same model.

@Sara

Absolute legend! That's exactly the info I was searching for. This is going to save me so much time probing in the dark. Seriously, thanks a ton for sharing the link!

Hi there,

I also have the ASTON MARTIN Racing Aspire and just downloaded the manual you shared. I'm pretty new to board-level phone repair, and this is a bit intimidating with all the tiny test points and the schematics. Could you point me in the right direction on how to start troubleshooting this ? Any advice on the first few things I should check would be a massive help.

Thanks so much for your time

General advices: start by checking the voltage at the battery connector on the board. With a known-good battery connected, you should see a steady voltage between 3.7V and 4.2V. After that, a great next step is to check the main power management IC (PMIC) for shorts. Using your multimeter in diode mode, check for shorts on the large input capacitors surrounding the PMIC.

Here are a few useful references for troubleshooting your device:
https://xdaforums.com/t/connecting-s7-edge-via-vysor-app.3370504/
Take a look at comment #867
Also, this : https://www.ifixit.com/Wiki/Samsung_S760_Troubleshooting.
You can also check this video starting from minute 8:

The ASTON MARTIN Racing Aspire service manual and boardviews from the link above were exactly what I've been searching for. I couldn't find a complete, free copy anywhere else. Seriously, thank you for sharing this you're a lifesaver!

Hi everyone, I'm working on a ASTON MARTIN Racing Aspire with a no power issue and need some guidance with my measurements.
I'm detecting 3.3V on the VREG_MAIN line (pin 1 of the PMIC), which looks good, but I'm getting 0V on the VDD_CPU line (pin 8) where the schematics indicate I should see about 0.9V.
Since this is a core voltage for the application processor, could this missing rail be why the device shows no signs of life?
What's the best procedure to diagnose this further? Should I check for shorts on the CPU rail first, or look at the PMIC's enable signals?
I've already verified the main 3.3V and 1.8V power rails are present and stable.

My ASTON MARTIN Racing Aspire was working perfectly until yesterday when it suddenly went completely dead. Now it won't respond to the power button, doesn't vibrate, and shows no signs of life even when connected to a charger. I'm worried there might be a serious issue.

I have a decent multimeter, a basic soldering iron, and a healthy dose of patience. While I've successfully replaced iPhone batteries and charging ports, this will be my first attempt at actual diagnosis. The sheer density of BGA chips and microscopic components is honestly a bit overwhelming.

I'm particularly curious about the alcohol trick I've seen online where you apply isopropyl to the board and look for evaporation hotspots to locate shorts. Is this actually a reliable method for beginners, or are there better approaches I should try first with just a multimeter?

I learned this lesson the hard way last month with mine, it was declared "dead" by two different shops. The phone showed absolutely no signs of life - no charging indicator, no vibration, nothing. Before diving into complex board work, I decided to try one more basic test: wireless charging.

To my complete surprise, it actually heated up on the charging pad! This single discovery completely changed my diagnostic path. It turned out the issue wasn't with the main board or processor, but with the notoriously fragile USB-C port that had failed completely. A $15 replacement part and some careful soldering brought it back to life.

The moral? Always exhaust every external testing method before opening the device. Test wireless charging if available, try different charging methods, and don't assume the worst case scenario. Sometimes the most "dead" devices have the simplest solutions hiding in plain sight.

I suspect my issue might be related to that cheap, third-party fast charger I used at the airport last week... Now the device gets extremely hot during charging, the screen flickers at low brightness, and sometimes it randomly shuts down at 30% battery. Could this have damaged the power management IC or battery calibration?

If your ASTON MARTIN Racing Aspire starts acting up, random reboots, fast battery drain, or connectivity issues, there are several diagnostic steps you can take before assuming the worst:

• Check your charging habits: Using poor-quality chargers or wireless pads can gradually damage your battery and charging circuit, leading to unpredictable behavior.
• Inspect the physical components: A slightly damaged charging port, worn battery, or even accumulated pocket lint can cause issues that seem like major hardware failures.
• Monitor temperature patterns: If your phone gets unusually hot during specific tasks (like camera use or gaming), it could point to a failing component rather than a software issue.
• Use diagnostic tools wisely: Ampere for battery health, phone diagnostic codes (*#0*# on many models), and a thermal camera can reveal problems without opening the device.
• Know when to stop: If you see liquid damage indicators tripped or smell burnt electronics, it's time to consult a professional before causing irreversible damage.

Also visit this link it may help : https://www.ifixit.com/Wiki/Shark_Rocket_Professional_Troubleshooting

Here's what I discovered on forums and technical databases:

Ensure all components (headphone jack, charging port, microphone, etc.) align with their respective openings and mounting points. Healthy Sensor: Readings should change smoothly and predictably as the phone rotates. Burn-in, more accurately called image retention or ghosting, occurs when static images or elements (like navigation bars, status icons, or keyboard outlines) are displayed on the screen for prolonged periods, causing those pixels to degrade unevenly and leave a faint, permanent ghost image visible even when new content is displayed. Before embarking on this delicate repair, thorough preparation is paramount. A damaged lens cannot be repaired; it must be replaced, often requiring a complex and costly repair involving the entire camera module. Incorrect Part: Ensure the replacement part is specifically for your phone model and version. Plastic Spudgers and Opening Picks: These non-conductive tools are crucial for safely prying open phone assemblies, disconnecting flex cables, and navigating delicate internal components without causing damage. Detecting motherboard flex damage is challenging because the symptoms are so diverse and often mimic other issues. Carefully align the new USB-C connector with the pads and anchor holes. They should have similar values (often around 0.5V, but varies by model). However, simply bridging a connection is not enough; for maximum reliability and longevity of the repair, the advanced placement and securing of jumper wires demand meticulous precision, the right materials, and a deep understanding of electrical principles. Understanding smartphone circuit protection and mastering fuse replacement is an essential skill for any advanced repair technician, ensuring the safety and longevity of the devices they work on.7. Any remaining residue will prevent the new adhesive from forming a strong bond, leading to the new screen lifting prematurely. The direct, intense light from the flash can make haze significantly more apparent, as it causes light to scatter aggressively within the hazy layer, resulting in a very washed-out, overexposed-looking image even if the exposure itself is technically correct. Ensure that haptic feedback is actually enabled in your phone's settings. Some motherboards might come pre-programmed with a generic IMEI that can be overwritten, while others might be entirely unassigned. Inspect for Damage: Before installing a new battery, inspect the phone's interior for any damage caused by the swollen battery (e.g., bent frame, damaged flex cables, cracked display). Logic Board Inspection: Examine the area of the logic board immediately around the speaker connector and the audio IC (often a larger chip near the connector). Inspect the motherboard itself for any residual dust, fingerprints, or foreign particles, especially around connector pads and screw holes. While phone is on: Press and hold the Power button until power options appear. Always combine LCI status with a thorough visual inspection for actual corrosion and water residue. For most users, a faulty baseband chip often necessitates a logic board replacement or a new phone. Clean and Organized Workspace: A clutter-free, well-lit surface is essential. The fundamental rule is: never replace the IR Emitter or Dot Projector with a non-original part if you want Face ID to work. Hot Air Rework Station (optional, but useful): For very small fuses or if working near sensitive components. Addressing the "charging but not increasing" issue requires patience and methodical troubleshooting. Crucial: Do not use too much adhesive, as it can seep inside and glue the button to the internal switch, rendering it inoperable. Poor Design: Some smartphone models inherently have less effective thermal management systems. Understanding their function and proper replacement is essential for comprehensive smartphone repair and maintenance. Uniform Green/Pink Tint: The entire screen has a dominant green or pink hue.

@Sherry, Not sure what you're trying to say but ok :)